Testing Equipment

Product Details:

Product Details:

Product Details:

FEATURES :

l This instrument have various Current Ranges 0.1 mA, 1 mA, 10 mA, 100 mA, 1A & 10A

l Resistance range 2 milli Ohms to 2 Kilo Ohms

l Attractive 4 ½ Digit Digital Display for readings

l Specially designed long lasting Lithium Ion battery which helps to conduct upto 50 tests on a single charge.

l For better Accuracy an intelligent Warm-up mode has been incorporated in 10A range.

l Smart Result Holding system for hassle free operation is incorporated.

Easy toggling between Contact Resistance mode and Winding resistance mode.

Product Details:

• Capable to test up-to 6000 Amp
• Available in Manual/Motorized Mode
• Ammeter for Output Current Measurement
• Digital / Analog Display
• Digital Time Interval Meter
• Bench type Control Panel
• Over current Protection
• Relay Protection
• HRC Fuse Protection
• Short Circuit Protection
• High Current ‘ON’ Indication
• Zero Start Interlock Facility

Product Details:

Insulation analysis within wide range

The Sonel MIC-15K1 insulation resistance meter has been designed to measure insulation resistance of electrical power engineering objects, including single and multi-core cables, transformers, motors and generators, condensers, circuit breakers and other power station equipment. It is especially recommended for measurements in areas with very high electromagnetic disturbances, e.g. at substations with a voltage of 1200 kV AC or 500 kV DC. Due to the measuring voltage of 15 kV (in accordance with the guidelines of ANSI/NETA ATS-2009 TABLE 100.1 standards) the meter can be used for objects with nominal voltage above 34.5 kV.

The MIC-15k1 is an extremely modern, ergonomic device with intuitive operation. It will satisfy even the most demanding measuring engineers in the most difficult conditions, with large disturbances, where other meters will be useless.

 Features

• Partial discharge indicator PDI.
• Diagnostics of insulation systems based on standard measurements of IR, DAR, PI, SV, RT, DD.
• It allows testing the electrical durability of the tested object - breakdown voltage indication.
• High resistance to electromagnetic interferences guarantees uninterrupted work in power stations and in close proximity to high voltage transmission lines up to 1200 kV AC and 800 kV DC.
• The function of smooth voltage rise in time (RT - Ramp Test) allows to state the partial discharges in the facility and to carry out a partial location of their occurrence.
• Efficient converter with a power of ~150 W that enables insulation burnout, allowing for pinpointing the location of cables and wires short circuit using one of the following:
  • visual method (if power cables are visible along the entire length),
  • reflectometric methods, seismic-acoustic waves detector, or with A-frame to indicate direction of the fault (the conductor must be buried in the ground with earth direct contact).
• Compatible with external software.

Application

MIC-15k1 meter is designed to measure insulation resistance of power objects, i.e.:

• single- and multicore cables,
• transformers,
• motors and generators,
• capacitors, switches and other devices installed in power stations.

It is especially recommended for measurements in areas with very high electromagnetic disturbances, e.g. electrical substations with 1200 kV AC and 800 kV DC. Thanks to the 15 kV measuring voltage (in accordance with ANSI / NETA ATS-2009 TABLES 100.1) the meter can be used for measuring objects with a nominal voltage above 34.5 kV.

Capabilities of the device

Highly efficient HV inverter, with test voltage of 15 kV and current up to 10 mA, suitable for measuring the insulation resistance up to 40 TΩ. Achieving such a result makes these meters unrivalled devices. Three-wire resistance measurement, performed using a "GUARD" wire, eliminates surface leakage currents caused by contaminated insulation, thereby increasing the reliability of obtained results.

The meter indicates the Dielectric Absorption Ratio DAR, Polarization Index PI and the value of Dielectric Discharge DD.

The device allows user to assess the condition of the insulation, by applying the test voltage incrementally in steps (SV - Step Volatge) or smoothly (RampTest - RT).

• SV method ensures that a dielectric in good condition will provide the same results, regardless of the applied voltage.
• RT method allows to determine the characteristics of the insulating material. The meter smoothly increases the measuring voltage without exposing the object to so-called electrical stress. 

Additional Information:

• Production Capacity: 1
• Delivery Time: 10
• Packaging Details: BOX

Product Details:

Additional Information:

• Production Capacity: 50 Number per month
• Delivery Time: 7 Days
• Packaging Details: Wooden Box Packing